In the pharmaceutical, building materials and food industries, on vessels and silos, on platforms and dosing systems, right around kitchen and bathroom scales ? weight is measured everywhere. In industry, it becomes particularly interesting with regards to the particular level in vessels. There are many possibilities for weight measurement or weighing. The filling level can be determined optically, hydrostatically, by ultrasound, microwaves and radar, mechanically, capacitively, by heat dissipation, by displacement and resistance or, what this short article is about, gravimetrically.
The term gravimetric is composed of the Latin ?gravitas? for ?gravity? and the Greek ??? ??????? for ?measure?. In gravimetric measurement, therefore, the heaviness of the mass is combined with the weight force to create a meaningful value and thus the level depends upon weighing vessels (the filling level results from the density of the medium and the geometry of the vessel). This makes gravimetric level measurement a part of weighing technology.
Gravimetric level measurement is specially suitable when uneven distribution can occur within the vessels.
Gravimetric level measurement: Advantages
This kind of weighing has several advantages. Possibly the greatest advantage is that the force transducers used for gravimetric level measurement can be found outside the vessel. Thus, they do not come into contact with the product. Nor is it essential to open or modify the vessels. Contamination can thus be eliminated. Cleaning can be much easier. Furthermore, very precise measurement is possible ? 0.02 % of the rated load is not uncommon when it comes to relative linearity error. This makes dosing possible when, for example, food is filled into bags ? not to mention the packaging must contain the amount specified.
Another advantage is that the product will not influence the measurement. The particular level can be determined gravimetrically for all contents ? solids, liquids, viscous substances, foaming substances ? even toxic or aggressive contents can be viewed as. Furthermore, the measurement is not falsified even if voids or uneven contents distribution occur in the silo or tank, as the entire contents are weighed.
Suitable mounting modules not merely ensure that the weight force is properly led into the force transducers, they also make installation super easy. The module and force transducer have a minimal height and a little installation volume. However, it really is problematic if the vessels are already permanently installed and may only be positioned on modules with significant amounts of effort. Then it really is probably advisable to bolt strain transducers to the supports. Any risk of strain transducers determine the compression of the supports due to the weight of the contents. They thus make it possible to weigh immovable vessels gravimetrically.
Gravimetric level measurement: Disadvantages
The disadvantages of gravimetric level measurement vary in significance based on the application. Results are mainly distorted when force shunts cannot be prevented. Ideally, the vessel ought to be mechanically decoupled. Used, however, it could always happen that, for example, struts are essential. Then it depends on what great their supporting effect is. Similar problems can occur if the measurement is influenced by a high bearing weight. The low the weight of the vessel when compared to product, the more accurate the gravimetric measurement. Finally, free-standing outdoor vessels can be suffering from natural factors. For instance, if wind pushes or snow leads to a significant increase in weight.
Typical force transducers for the weighing of vessels
Single point load cells are classically used for scales. These not merely have a minimal price and high accuracy, however the weight is also determined reliably, no matter where it is placed on the platform. For optimal force introduction, bending or shear beams with the corresponding weighing modules are often installed under tanks, silos or vessels that stand on supports. To look for the rated load of these force transducers, divide the total weight of the vessel by the number of supports. If the rated load exceeds 10 t, you’ll be able to switch to compression force transducers, the utmost capacity which reaches around 300 t. With four supports, vessels of up to 1,200 t can be weighed with the best accuracy. Alternatively, Peril can be suspended from S-type force transducers or fitted with strain transducers.
Note
Level could be measured in many various ways. Whether gravimetric as described, or with a submersible pressure sensor, float switch or pressure sensor ? WIKA gets the right sensor for every application. Do you want to buy the products? Inside our WIKA online-shop you will find some of our standard designs. For those who have any questions, your contact will gladly help you.
Also read our posts
Bending beam and shear beam in weighing technology
Practical application of strain transducers